MineralPlus Swift Twist Pro RO
Reverse Osmosis Filtration System

Parts Checklist

	RO Manifold with Sediment, Carbon, Reverse Osmosis, and MineralPlus/Post Carbon Filters
	Water Storage Tank
	Air Gap RO Faucet and Non-Air Gap Faucet (Sold Separately)
	Feed Water Adapter and Components
	Color Tubing Set
	Drain Saddle
	Storage Tank Valve
	Leak Detector Valve
	Leak Detector Tray
	Leak Detector Valve Screws
	Leak Detector Pads
	Fittings and Teflon tape (package quantity may vary)

Tool List

We recommend having the following tools on hand to help with the installation process:

	Tube Cutter (included in parts bag)
	Phillips Screwdriver
	Adjustable Wrench
	Variable Speed Electric Drill
	3/8" Drill Bit for Drain Saddle
	Bucket
	Cloths
	1/8" Diamond-Tip Drill Bit (if installation requires faucet opening)
	1" Diamond-Tip Drill Bit Hole Saw (if installation requires faucet opening)

Advanced 5-Stage RO Filtration Process

Use the color-coded tube connections to complete the installation more easily:

Determine the Location for the RO System, RO Faucet, and Water Storage Tank

• The faucet can be installed in a pre-drilled hole on the sink if available. If drilling a new hole, make sure not to damage any plumbing or wiring that may be under the countertop or sink.
• The pressure storage tank can stand vertically upright or lay horizontally. We recommend intalling it vertically to get the most life out of your tank.
• The storage tank and RO faucet can be up to 5 feet apart. If the tank needs to be farther away than 5 feet, we recommend a booster pump to supply adequate pressure at the faucet.

Tubing Connection Tips

Insert Tubing	Release Tubing

Installation Instructions

Warnings:

• This system is for cold water supplies only. Do NOT install the system on the hot water supply line. Hot water will damage the system.
• Installation and use must comply with all state and local plumbing codes.
• This system unit is for indoor use only.
• A pressure regulator is required if incoming water pressure is over 80 psi.
• It is highly recommended to shut off the water supply to the system unit when it will not be in use for longer than a week.
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Feed Water Adapter Installation

Attention: The water supply line to the system must be from the cold water supply line only. Hot water will severely damage your system

1. Locate the feed water adapter and stainless steel fittings. Ensure o-rings are installed inside the feed water adapter and stainless steel fittings. Thread stainless steel fittings onto the feed water adapter. Tighten using a wrench.

   

2. Turn off the cold water supply to the faucet by turning the feed water adapter valve completely off.
3. Open the cold water sink faucet to relieve pressure from the water line.
4. Prior to disconnecting the faucet connector, lay down a bowl or bucket to catch any water drips. Unscrew the kitchen faucet connector pipe from the cold water supply valve.
5. Connect the female end of the feed water adapter to the cold water shut-off valve. Check that the O-ring in the kitchen faucet connector pipe is still properly seated. Connect the kitchen faucet connector pipe onto the male end of the feed water adapter, tightening with a wrench or pliers.

   

6. Remove the blue locking clip from the feed water adapter. Insert the 1/4" white tubing that goes to the reverse osmosis system. Reinsert the locking clip.

   

Faucet Installation

Note: Some sinks have pre-drilled 1" holes that are suitable for installation of your Drinking Water faucet. If your sink has such a hole, skip to the faucet installation instructions.

Notice: Please refer to recommendations from the countertop or sink manufacturer or a professional for drilling a hole in a countertop or sink. The RO system manufacturer and supplier do not accept any responsibility for damage resulting from installing faucets in any surface, including but not limited to granite, marble, or porcelain sinks.

Recommendation for granite or marble countertops, porcelain sinks, and other surfaces: ALWAYS use a qualified professional for drilling a hole because these materials can crack and chip easily during the process.

SP-FC100 Faucet Installation Instructions



1. Start by sliding the escutcheon onto the bottom of the faucet, lining up the holes on the base plate with the 3 inlet/outlet port stems on the faucet. The escutcheon has the rubber O-ring preinstalled.
2. (Air Gap Installation Only) Before mounting the faucet, install the waste water tubing on the faucet. The 1/4” blue filtered water tubing is already connected for convenience. First, push the 1/4" black wastewater tube onto the smaller, 1/4" air gap barb fitting at the bottom of the faucet, making sure to push it at least 1/2" up the fitting.
3. (Air Gap Installation Only) Push the 3/8" red wastewater tube onto the 3/8" air gap barb fitting at the bottom of the faucet, making sure to push it at least 1/2" up the fitting.
4. Insert the blue, red, and black tubing and the stem through the pre-drilled hole.
5. From the underside of the sink, slide on the slotted metal washer, spacer, star washer, washer, and mounting nut.
   • Check the orientation of the faucet, then tighten the locking nut securely with a wrench. Do not overtighten fittings.
   • (Optional) Install the spacer if the countertop is less than 1/2" thick (e.g., a stainless steel sink). You do not need a spacer if your countertop thickness is 1/2" or more.
6. Connect the 1/4” blue filtered water hose to the outlet on the RO membrane.
7. (Air Gap Installation Only) Connect the other end of the 1/4" wastewater line to the RO system’s wastewater output port.
8. (Air Gap Installation Only) Connect the other end of the 3/8" wastewater line to the drain saddle.
9. Flush the faucet with water and check for leaks.

SP-FC210 Faucet Installation Instructions



1. (Air Gap Installation Only) Before mounting the faucet, install the water tubing on the faucet. Begin by pushing the 1/4" wastewater tube onto the smaller, 1/4" barb fitting at the bottom of the faucet, making sure to push it at least 1/2" up the fitting.
2. (Air Gap Installation Only) Push the 3/8" wastewater tube onto the 3/8" barb fitting at the bottom of the faucet, making sure to push it at least 1/2" up the fitting.
3. Slide the escutcheon base of the faucet up over the water lines, and insert it into the bottom of the body of the faucet.
4. Insert the faucet lines and stem into the hole on the countertop or sink. For the next few steps, it may be easier if you have a second person hold the faucet in position above the counter.
5. Underneath the counter, insert the black rubber washer in the proper position over the water lines and faucet stem, making sure to line up the pieces with the hole on the washer.
6. Slide on the metal washer against the rubber washer and then slide up the plastic spacer. It may be easier to try and mount both pieces simultaneously.
7. Screw the black lock washer wing nut onto the threaded faucet stem under the metal washer or optional spacer, making sure to tighten but not overtighten.
8. Depending upon the size of your undersink water filter’s filtered water hose, screw the 1/4" or 3/8" union adapter onto the end of the threaded faucet stem. Be sure to tighten but not overtighten.
9. Connect the filtered water hose from the undersink water filter system to the union adapter.
10. (Air Gap Installation Only) Connect the other end of the 1/4" wastewater line to the RO system’s wastewater output port.
11. (Air Gap Installation Only) Connect the other end of the 3/8" wastewater line to the drain saddle.
12. Flush the faucet with water and check for leaks.

Mounting the Drain Saddle

Warning: The drain saddle creates a wastewater connection with the sink drain and is designed to fit a standard 1-1/2" OD drain pipe. Drain saddles should always be installed at least 1-1/2" above the nut of the p-trap on a vertical or horizontal drain. Do not install near a garbage disposal. Take extreme caution to only drill through one side of the drain pipe.

1. Locate a spot at least 1-1/2" above the nut of the p-trap on the drain pipe that is convenient for installing the drain saddle. It is recommended to install on horizontal piping to minimize dripping noise.

   

2. The small, square, black foam gasket with a circle cut out of the middle must be applied to the inside of the drain saddle. Remove the backing and stick to the drain saddle as shown.

   

3. Using the 3/8" drill bit, drill into one side of the drain pipe. Do Not drill through both sides of the pipe.
4. Assemble the drain saddle around the drain pipe and align the opening with the hole drilled in the previous step - you may use a small screwdriver to feed through the drain saddle hole to aid with the alignment.

   

5. If using an Air-Gap faucet measure the 3/8" red tube from the faucet to the drain saddle on the drain pipe and make a straight cut to the correct length. If using a Non-Air gap faucet utilize the 1/4”x3/8” reducing QC fitting to connect the 1/4” black tubing to the 3/8” red tubing. Reference 4-stage filtration process.

   

Notice: The red 3/8" drain tube to the drain saddle must be as SHORT and STRAIGHT as possible. Make sure there is a downward slope from the faucet to the drain saddle to allow for proper drainage without causing the tube to stretch or sag.

Tips:

1. If tubing is looped, it can cause water to come out of the air gap faucet.
2. Looped tubing can shorten the life expectancy of the RO membrane.

Installing the Storage Tank Valve

Warning: Do not adjust the air valve on the storage tank. It has been preset to 8-10 psi by the manufacturer. If the tank will not fill with water, then it may be overpressurized. Speak to your installer, or carefully let a bit of air out of the tank. If you let out too much, you will need to repressurize the tank with a bicycle pump.

1. Remove the plastic stand at the top of the tank.
2. Use the Teflon tape to wrap the 3/8" fitting at the top of the tank 6 times. Then thread the storage tank valve onto the fitting.

   

3. Place the storage tank in the desired location, and position either horizontally or vertically. We recommend placing the tank vertically. Horizontal placement can stress the tank's internal bladder, causing early tank failure.

   

4. Insert the yellow tubing in the port marked tank on the side of the RO manifold and into the storage tank valve until tubing stops. (see the Advanced 4-Stage RO Filtration Process diagram for reference).
5. Turn off the storage tank valve.

   

Installing the Leak Detector Kit & Tray

Determine which of the tray’s six mounting points you will use to install the detector, depending on likely leak points. Ensure that your system will fit with the placement of the detector. Set the detector on its mounting position, but do not install it or the cotton pad yet.

Place the leak detector tray (with detector placed, but not secured) in your under-sink cabinet, and place your filtration system inside the tray. Most RO undersink systems will fit. The usable internal dimensions with detector mounted (any position) are:

Usable Inside Length: 15 ½”

Usable Inside Width: 7”

Ensure that the fit is good, and your hoses will reach the detector valve.

If you are using the optional SP-LD133-BRK Wall Mount Brackets with a mounted filter system, find a suitable place beneath your system, and pre-drill holes with a power drill. Install the brackets with the provided screws and hang the tray beneath your system.

The leak detector valve goes between the feedwater line under your sink and the RO system. The cotton pad that goes inside the detector expands when exposed to moisture, depressing a valve in the detector that cuts off the feedwater, protecting your home from potential water damage.

Warning: The valve is highly sensitive to water. Please install with caution, as the leak detector pad easily absorbs water and will require replacement every time it comes into contact with water.

To Install Leak Detector:

1. Screw the leak detector valve to the tray mounting points you have chosen.
2. Measure from the feed water adapter to the leak detector inlet and cut the 1/4" white inlet tubing. Cut only with angle cutters or a razor blade. Do not use scissors or a knife, as these can crimp and damage the hoses, resulting in leaks.

   

3. Measure from the feed water adapter to the leak detector inlet and cut the 1/4" white inlet tubing. Cut only with angle cutters or a razor blade. Do not use scissors or a knife, as these can crimp and damage the hoses, resulting in leaks.
4. Connect the tubing from the feed water valve to the inlet port of the leak detector valve.
5. Measure from the outlet of the leak detector to the RO inlet port, and cut to length.
6. Connect the 1/4" white tubing from the outlet port of the leak detector to the RO inlet port.

Proceed to next step before installing cotton pad.

Starting the System

Warning: Make sure all tubing has been properly connected. Check that all of the connections are secure before turning on the water supply. The leak detector cartridge should be installed after initial system startup. This is to ensure the leak detector cartridge does not need to be replaced during startup due to tubing that is not inserted properly. Refer to the checklist and diagram below:

• The blue faucet tubing connects to the side of the RO manifold labeled Faucet.
• The white water-supply feed tubing connects to the side of the RO manifold labeled Inlet.
• The yellow storage tank tubing connects to the side of the RO manifold labeled Tank.
• The 1/4" black wastewater tubing from the RO will connect to the Air-Gap faucet or if utilizing a Non-Air gap faucet it will connect to the 1/4”x3/8”QC reducing fitting.
• The 3/8" red wastewater tubing from the RO faucet connects to the drain saddle. If using a Non-Air gap faucet the red tubing will connect to the 1/4”x3/8” reducing fitting to the drain saddle.

1. Close the storage tank valve.
2. Turn on the cold water supply and the feed water adapter valve. If leaks are present, turn off the cold water supply and correct the problem before proceeding.
3. Turn on the RO faucet to release any air from the system.
4. After several minutes, water will begin to drip or trickle from the RO faucet.
5. Let it trickle for approximately 10 minutes, then turn off the RO faucet.
6. Turn on the storage tank valve. It will take 1 to 3 hours for the storage tank to fill, depending on your home’s water pressure. You will know the tank is full when you hear the water stop running to the drain pipe.
7. After the tank is full, flush the system by turning on the RO faucet until the water in the tank is completely discharged. Warning: Do NOT drink the first tank of water produced by the system. We recommend refilling and flushing the tank twice before use.
8. After the tank is emptied, turn off the RO faucet and allow the tank to refill. Refilling will usually take 1 to 3 hours.
9. Turn on the faucet and allow the tank to flush once more.
10. Turn off the faucet and allow another 1 to 3 hours for the tank to refill.
11. Once you have determined the RO system has no leaks, close the feed water adapter valve, open the leak detector drawer, and install the cartridge/pad. Close the leak detector drawer and open the feed water adapter valve.

    

12. After the tank has refilled for a third time, you can begin to enjoy your clean, freshly filtered water.

Check daily for leaks during the first week of use. Check for leaks periodically after the first week.

Water may be milky or cloudy during the first week of use. This is caused by air bubbles in the water and is normal. The water is completely safe to drink and use.

Recommended Maintenance

To help your system achieve maximum efficiency and service life, perform the following recommended maintenance procedures.

Note: This RO system utilizes filter cartridges that must be periodically replaced to maintain system performance. Frequency of changes may vary depending upon water quality.

Filter Replacement Set

MineralPlus Swift Twist Pro RO Replacement Set	One Year Filter Replacement Set

• Filters may be stored for several years.
• Store unopened, sealed filters in an airtight container to extend shelf life and protect from unwanted odor.

Membrane Cartridges

• Dry-packed RO membrane cartridges typically have a one-year shelf life. To extend shelf life, keep the unopened, sealed membrane element in a refrigerator.
• After the first use, run the RO system every day for 10-15 minutes to maintain membrane performance.
• If the RO system will not be used for several weeks, drain the storage tank completely. Be sure to fill and drain the tank 2 times before using the system again after a period of non-use.

Replacing Filter Cartridges

Our system includes a check valve, also known as a flow restrictor, to control the flow of the water and prevent water from spurting out of the system during cartridge changes, allowing you to quickly and easily change the filter cartridges without shutting off the water supply. However, there is always a little bit of water left in the filter head from system operation, so please follow the steps below:

1. Lay cloths down to catch any spills while changing the filters, making sure to cover the leak detector to protect it from any possible splashes.
2. Turn off both the feed water valve and the storage tank valve.
3. Turn on the RO faucet.
4. Pull the bottom of the cartridge out and twist left until the cartridge pops out.

   

5. Unwrap the filter cartridge, line up the unlock key, insert filter and twist right until the lock key is lined up

   

6. Replace all 4 filter cartridges.
7. Once all of the cartridges have been replaced, turn on the water supply and check for leaks. It may take 10-20 minutes for flow rate to return to normal after installation of the new membrane
8. When flow rate has returned to normal, turn on the storage tank valve. After 1 minute, turn off the RO faucet.

Warning: Do NOT drink the first tank of water produced by the system. We recommend refilling and flushing the tank twice before use.

Troubleshooting

Warning Turn off the system before servicing or inspection.

Specification And Performance Data

Water Treatment Parameters

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

This system has been tested according to NSF/ANSI 58 and NSF/ANSI 372 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF/ANSI standard 58 and NSF/ANSI 372.

*Claim reduction percentage verified through manufacturer testing.

The efficiency rating percentage represents how much influent water is produced as filtered water under testing conditions that approximate normal daily usage.

Testing results were performed under designated standard individual laboratory; actual conditions and performance may vary.

Warranty

The manufacturer warrants that the water filtration system delivered will be free from any defects in workmanship or materials. If your MineralPlus water filtration system fails because of a manufacturing defect within one (1) year from the date of the original purchase, contact your dealer--the manufacturer will exchange the defective water filtration system for a new identical water filtration system without charge.

The manufacturer's obligation to the customer under these warranties shall be limited, at its option, to replacement of items covered by these warranties.

Damage to any part of this system because of misuse, misapplication, negligence, alteration, accident, installation, or operation contrary to our instructions, incompatibility with accessories not made by the system manufacturer, or damage caused by freezing, flood, fire, or Acts of God are not covered by this warranty. In all such cases, regular charges will apply. This limited warranty does not include service to diagnose a claimed malfunction in this unit. This warranty is void if the claimer is not the original purchaser of the unit or if the unit is not operated under normal municipal water or well water conditions.

We assume no warranty liability in connection with this system other than that specified herein. This warranty is in lieu of all other warranties, expressed or implied, including warranties of fitness for a particular purpose. The manufacturer’s liability hereunder shall not exceed the cost of the product. Under no circumstances will the manufacturer be liable for any incidental or consequential damages or for any other loss, damage, or expense of any kind, including loss of use arising in connection with the installation or use or inability to use the covered items. These warranties may change at any time without notice.

Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from state to state. You should consult applicable state laws to determine your rights. So far as is consistent with implied warranties of merchantability and fitness for a particular purpose, the warranties are limited in duration to one (1) year from the date of original shipment.